{"id":1686,"date":"2026-08-24T18:45:16","date_gmt":"2026-08-24T10:45:16","guid":{"rendered":"https:\/\/www.biaotuoboard.com\/xps-waterproof-backer-board-substrate-preparation-framing-guide\/"},"modified":"2026-08-24T18:45:16","modified_gmt":"2026-08-24T10:45:16","slug":"xps-waterproof-backer-board-substrate-preparation-framing-guide","status":"publish","type":"post","link":"https:\/\/www.biaotuoboard.com\/xps-waterproof-backer-board-substrate-preparation-framing-guide\/","title":{"rendered":"XPS Waterproof Backer Board Substrate Preparation &#038; Framing: Stud Spacing, Blocking, Flatness &#038; Fastening Requirements (2026)"},"content":{"rendered":"\n<h2 class=\"wp-block-heading\">Why the Wall Behind the Board Decides Whether Your Shower Lasts<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Every tile installation is only as good as the surface it is fastened to. An XPS waterproof backer board can be perfectly sealed, correctly banded, and flawlessly tiled \u2014 and still fail if the framing behind it flexes, bows, or was never blocked in the right places. Closed-cell extruded polystyrene is lightweight and rigid, but it is <em>not<\/em> a structural material. It transfers every load, every deflection, and every point of movement back to the studs and blocking underneath. In this guide we break down exactly how to prepare that substrate so the waterproofing you apply on top stays intact for decades.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This is the \u00abbefore you install\u00bb companion to our full XPS backer board series. If you have not yet read the <a href=\"https:\/\/www.biaotuoboard.com\/waterproof-backer-board-complete-guide-xps-tile-substrates\/\">complete material guide<\/a>, start there for fundamentals; when you are ready to fasten panels, cross-reference our <a href=\"https:\/\/www.biaotuoboard.com\/install-xps-waterproof-backer-board-step-by-step-guide\/\">step-by-step installation guide<\/a>. What follows is the framing and substrate preparation that must happen <em>first<\/em>.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Stud Spacing: The First Number That Matters<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Stud spacing controls how much unsupported panel area exists between fasteners, which in turn controls tile deflection. The universal rule for tile backer boards is <strong>16 inches on center (o.c.)<\/strong> for both wood and metal studs. Some foam-board manufacturers permit up to <strong>24 inches o.c.<\/strong> in non-load-bearing, low-moisture walls, but this is almost never worth the risk in a shower or wet room. Here is the practical guidance:<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th>Application<\/th><th>Recommended Spacing<\/th><th>Maximum Allowed<\/th><th>Notes<\/th><\/tr><\/thead><tbody>\n<tr><td>Shower \/ tub surround walls<\/td><td>16&#8243; o.c.<\/td><td>16&#8243; o.c.<\/td><td>Do not exceed; spray zones carry extra live load<\/td><\/tr>\n<tr><td>Dry vanity \/ non-wet partition<\/td><td>16&#8243; o.c.<\/td><td>24&#8243; o.c.<\/td><td>Verify foam-board manufacturer&#8217;s max before exceeding 16&#8243;<\/td><\/tr>\n<tr><td>Steam room \/ sauna walls<\/td><td>12&#8243; o.c.<\/td><td>16&#8243; o.c.<\/td><td>Closer spacing resists thermal cycling and vapor pressure<\/td><\/tr>\n<tr><td>Ceiling (tiled)<\/td><td>12&#8243; o.c.<\/td><td>16&#8243; o.c.<\/td><td>Ceilings see added dead load; see our <a href=\"https:\/\/www.biaotuoboard.com\/xps-waterproof-backer-board-steam-rooms-showers-guide\/\">steam room guide<\/a><\/td><\/tr>\n<tr><td>Floor (over joists)<\/td><td>Joists \u2264 16&#8243; o.c.<\/td><td>\u2014<\/td><td>See deflection section below; subfloor must meet L\/360<\/td><\/tr>\n<\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">A quick tip from the field: when you are forced into 24&#8243; o.c. framing, upgrade the panel thickness one step (for example, 20&nbsp;mm instead of 12.5&nbsp;mm) or add a mid-span blocking row. For a complete breakdown of panel thickness by application, see our <a href=\"https:\/\/www.biaotuoboard.com\/xps-waterproof-backer-board-thickness-size-selection-guide\/\">thickness and size selection guide<\/a>.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Deflection Limits: The L\/360 Rule and Why Foam Does Not Forgive<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Tile assemblies are rated by how much the supporting structure can bend. The governing standard \u2014 set out in the TCNA Handbook and the IRC\/IBC \u2014 is a deflection limit of <strong>L\/360<\/strong> for ceramic and porcelain tile, and <strong>L\/720<\/strong> for natural stone. In plain terms, a 10-foot span of ceramic tile may sag no more than about 0.33 inches; stone must hold to half of that.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Because XPS foam board is more flexible than cement board or gypsum board, an under-built floor or wall is felt <em>more<\/em> \u2014 not less \u2014 once tiles are bonded to it. If the framing deflects beyond limit, the grout is the first thing to crack, followed by the tiles themselves, regardless of how good the waterproofing is. Before any panel goes up, verify:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Floor joists:<\/strong> Check span, species, grade, and spacing against a span table; sister or add a beam if the calculated deflection exceeds L\/360 (or L\/720 for stone).<\/li>\n<li><strong>Subfloor:<\/strong> Minimum 3\/4&#8243; tongue-and-groove plywood or OSB, glued and screwed to the joists; add a second layer for stone or large-format tile.<\/li>\n<li><strong>Walls:<\/strong> Studs must be plumb, straight, and securely fastened top and bottom; a bowed stud must be straightened or replaced before boarding.<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\">Flatness and Plumb: The Tolerance Tile Actually Needs<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The larger the tile, the flatter the wall must be. This is a point many DIY installers miss, and it is one of the most common causes of visible lippage (uneven tile edges) and hollow-sounding tile. Current industry guidance for large-format tile (any side &ge; 15 inches) calls for a substrate variation of no more than <strong>1\/16 inch in 12 inches<\/strong>, and no more than <strong>1\/8 inch in 10 feet<\/strong> for standard tile. In practice this means shimming and planing studs until a straightedge reads nearly dead flat before the foam board ever goes up.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th>Tile Format<\/th><th>Max Substrate Variation<\/th><th>Recommended Prep<\/th><\/tr><\/thead><tbody>\n<tr><td>Standard tile (&lt; 15&#8243; any side)<\/td><td>1\/4&#8243; in 10 ft<\/td><td>Shim \/ plane studs; verify with 4 ft straightedge<\/td><\/tr>\n<tr><td>Large-format tile (&ge; 15&#8243; any side)<\/td><td>1\/8&#8243; in 10 ft, 1\/16&#8243; in 12&#8243;<\/td><td>Plane + shim; consider a leveling clip system at tiling stage<\/td><\/tr>\n<tr><td>Natural stone \/ gauged porcelain panels<\/td><td>1\/16&#8243; in 10 ft<\/td><td>Full shimming, plane studs, use L\/720 floor rating<\/td><\/tr>\n<\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">For a deeper look at achieving flatness on curves, niches, and luxury designs, see our <a href=\"https:\/\/www.biaotuoboard.com\/xps-waterproof-backer-board-design-guide-curves-niches\/\">design and creative applications guide<\/a>.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Blocking: The Detail That Prevents Every \u00abLater\u00bb Problem<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Blocking is the horizontal and vertical framing added <em>before<\/em> the board goes up so that every future attachment has something solid to bite into. On a foam backer board, blocking matters more than on cement board because the panel itself cannot carry a screw under load. Missing blocking is the number-one reason a shower seat feels spongy, a glass door pulls loose, or a grab bar pulls out of the wall. The checklist below covers the blocking you must install.<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Grab bars and handrails:<\/strong> Solid blocking (2\u00d76 or 2\u00d78) at the exact mounting height, marked and photographed before boarding. Required for ADA\/ANSI A117.1 compliance; see our <a href=\"https:\/\/www.biaotuoboard.com\/xps-waterproof-backer-board-curbless-showers-barrier-free-bathrooms\/\">barrier-free bathroom guide<\/a>.<\/li>\n<li><strong>Glass shower enclosures:<\/strong> Continuous blocking where hinges, brackets, and channels mount \u2014 typically both jambs and the header.<\/li>\n<li><strong>Shower seats and benches:<\/strong> Structural blocking engineered for a live load (commonly 250\u2013300&nbsp;lb plus tile weight), not just a few 2\u00d74s.<\/li>\n<li><strong>Niches and shelves:<\/strong> Framing that defines the niche opening and provides nailers for the niche&#8217;s inner panels.<\/li>\n<li><strong>Wall-hung vanities and heavy mirrors:<\/strong> Blocking at mounting locations, since foam board will not hold a lag screw.<\/li>\n<li><strong>Valve and shower-head drops:<\/strong> Backing to anchor the plumbing so the finished trim sits flush and rigid.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Record all blocking locations with measurements and photographs before the waterproofing goes on. Once the board is sealed and tiled, this documentation is the only way to find blocking again for a retrofit grab bar or glass install.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Fastening Schedule: Screws, Washers, and Edge Distance<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">XPS foam boards are fastened with <strong>corrosion-resistant screws and large-diameter sealing washers<\/strong>, never drywall screws and never nails. The fasteners do two jobs at once: they anchor the panel and they are sealed by the washer to maintain the waterproof barrier. The exact schedule varies by manufacturer, but the field-tested default is below.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th>Location<\/th><th>Spacing<\/th><th>Edge Distance<\/th><th>Detail<\/th><\/tr><\/thead><tbody>\n<tr><td>Wall field<\/td><td>12&#8243; o.c. max<\/td><td>\u2014<\/td><td>Even grid; washers set flush, never countersunk<\/td><\/tr>\n<tr><td>Panel perimeter<\/td><td>12&#8243; o.c. max<\/td><td>1&#8243; min from edge<\/td><td>Keep back from the edge to avoid crushing the foam<\/td><\/tr>\n<tr><td>Inside corners<\/td><td>6&#8243; o.c.<\/td><td>\u2014<\/td><td>Closer spacing prevents corner bowing<\/td><\/tr>\n<tr><td>Ceilings<\/td><td>8\u201312&#8243; o.c.<\/td><td>1&#8243; min<\/td><td>Closer spacing for added dead load<\/td><\/tr>\n<tr><td>Floor \/ pan areas<\/td><td>Per manufacturer<\/td><td>\u2014<\/td><td>Follow the pan manufacturer&#8217;s exact pattern<\/td><\/tr>\n<\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Set every washer <strong>flush with the surface<\/strong> \u2014 never driven deep enough to crush or dimple the foam, which weakens anchorage and creates a low spot that telegraphs through the tile. Over-driven fasteners are a leading cause of the failures covered in our <a href=\"https:\/\/www.biaotuoboard.com\/xps-waterproof-backer-board-common-mistakes-troubleshooting\/\">troubleshooting guide<\/a>.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Wood vs. Metal Studs: Preparing Both Correctly<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">XPS waterproof backer board performs well over both wood and steel framing, but each substrate has its own preparation rules.<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Wood studs:<\/strong> Use kiln-dried lumber (moisture content ideally below 19%) to reduce shrinkage and twisting. Plane or shim any stud that is out of plane, and crown studs so the crowns face the same direction. Fasten panels with coarse-thread, corrosion-resistant screws.<\/li>\n<li><strong>Metal studs:<\/strong> Use 20-gauge or heavier for tiled wet areas; thinner studs flex too much. Fasten with fine-thread, self-drilling, corrosion-resistant screws. Add wood blocking in the stud cavity where heavy attachments are planned, since foam board cannot be screwed into light-gauge steel under load.<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\">Coordinating Plumbing and Electrical Before the Board Goes Up<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The waterproofing layer is the wrong time to discover a valve is in the wrong place or a mixing valve sits proud of the wall. Coordinate the rough-in before boarding:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Valve depth:<\/strong> Set the mixing valve so the finished trim lands flush against the <em>finished<\/em> tile surface, accounting for board + thin-set + tile thickness. Test-fit the trim with a scrap of board and tile.<\/li>\n<li><strong>Penetrations:<\/strong> Locate every pipe and shower-head drop so they pass through the board at a clean, sealable point; prefab the seals or collars before fastening panels.<\/li>\n<li><strong>Drain placement:<\/strong> Confirm the drain location and height against the pre-sloped pan or mud bed before anything is sealed; see our <a href=\"https:\/\/www.biaotuoboard.com\/xps-waterproof-backer-board-curbless-showers-barrier-free-bathrooms\/\">curbless shower guide<\/a> for drain and slope specifics.<\/li>\n<li><strong>Electrical:<\/strong> Any outlets, heated floor thermostats, or lighting must be roughed in and their penetrations detailed to remain watertight.<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\">Subfloor and Floor Preparation for XPS Pan Systems<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">On floors, the XPS system usually sits over a pre-sloped foam tray or a mud bed, both of which need a clean, rigid, level subfloor. Confirm the subfloor is dry, free of debris and high spots, and structurally sound before placing the tray. Grind or float any unevenness so the tray bears evenly; a rocking or voided tray is a hidden future crack. For thermal integration under a heated floor, review our <a href=\"https:\/\/www.biaotuoboard.com\/xps-waterproof-backer-board-thermal-performance-radiant-floor-heating\/\">radiant floor heating guide<\/a>.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">A Pre-Boarding Checklist You Can Print<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Run through this list before the first panel is fastened, and you will have eliminated the vast majority of XPS substrate failures.<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Studs:<\/strong> 16&#8243; o.c. (12&#8243; for steam\/ceilings), plumb, straight, crowns aligned, securely anchored.<\/li>\n<li><strong>Deflection:<\/strong> Floor L\/360 (L\/720 stone) verified; no visible bounce or squeak.<\/li>\n<li><strong>Flatness:<\/strong> Within tolerance for the tile format (straightedge check in both directions).<\/li>\n<li><strong>Blocking:<\/strong> Installed for grab bars, glass, seats, niches, vanities, valves \u2014 and photographed.<\/li>\n<li><strong>Fastener stock:<\/strong> Corrosion-resistant screws + sealing washers on hand; no drywall screws or nails.<\/li>\n<li><strong>Plumbing\/electrical:<\/strong> Rough-in complete, valve depth test-fitted, penetrations located.<\/li>\n<li><strong>System:<\/strong> One manufacturer&#8217;s board, band, sealant, and drain chosen end-to-end (see our <a href=\"https:\/\/www.biaotuoboard.com\/xps-waterproof-backer-board-buyers-guide-brand-comparison\/\">buyer&#8217;s guide<\/a>).<\/li>\n<li><strong>Moisture:<\/strong> Wood framing at proper moisture content; no wet or swelling lumber.<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\">Frequently Asked Questions<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">Can I install XPS waterproof backer board over 24&#8243; o.c. studs?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Only if the board manufacturer explicitly permits it and the wall is non-load-bearing. For any shower, tub surround, or wet area, we strongly recommend 16&#8243; o.c. (or 12&#8243; for steam rooms). If you cannot change the framing, add a mid-span blocking row or step up one panel thickness to restore rigidity.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Does foam backer board need blocking behind the seams?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Panel edges should land on framing wherever possible, so planning stud and blocking layout to match your board dimensions avoids unsupported seams. Where a seam falls between studs, the manufacturer&#8217;s reinforcing band bridges it, but a floating seam is still a weak point \u2014 detail blocking so every board edge is supported.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">What is the minimum flatness tolerance for large-format tile?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Industry guidance is 1\/16 inch in 12 inches and 1\/8 inch in 10 feet for large-format tile, and 1\/16 inch in 10 feet for stone or gauged porcelain panels. If the framing does not meet this, shim and plane it before boarding \u2014 trying to correct flatness with extra thin-set on a foam panel is unreliable.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Do I need special screws for XPS foam backer board?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Yes. Use corrosion-resistant screws with the large-diameter sealing washers specified by the board manufacturer. Drywall screws are too brittle, lack the washer, and will rust and fail in a wet assembly. Match the thread type to the framing (coarse for wood, fine\/self-drilling for steel).<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">How do I support a grab bar if the blocking was forgotten?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Once the board is sealed and tiled, retrofitting a properly load-rated grab bar is difficult without opening the wall. If blocking was missed, use a manufacturer-approved surface-mount or through-wall grab bar system, or open the wall and add blocking before re-waterproofing. This is exactly why blocking must be photographed before boarding \u2014 see the ADA requirements in our <a href=\"https:\/\/www.biaotuoboard.com\/xps-waterproof-backer-board-curbless-showers-barrier-free-bathrooms\/\">barrier-free bathroom guide<\/a>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><em>This article is part of our ongoing series on XPS waterproof backer board. Explore the full library, from <a href=\"https:\/\/www.biaotuoboard.com\/waterproof-backer-board-complete-guide-xps-tile-substrates\/\">material fundamentals<\/a> and <a href=\"https:\/\/www.biaotuoboard.com\/xps-waterproof-backer-board-vs-cement-board-cost-roi\/\">cost comparison<\/a> to <a href=\"https:\/\/www.biaotuoboard.com\/xps-waterproof-backer-board-market-analysis-2026-growth-trends\/\">2026 market analysis<\/a>.<\/em><\/p>\n\n","protected":false},"excerpt":{"rendered":"<p>The complete framing and substrate preparation guide for XPS waterproof backer board. Covers stud spacing, the L\/360 deflection rule, flatness and plumb tolerances for large-format tile, blocking for grab bars and glass, fastener schedules, wood vs metal studs, plumbing rough-in coordination, floor prep, a printable checklist, and an FAQ.<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"default","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[21],"tags":[],"class_list":["post-1686","post","type-post","status-publish","format-standard","hentry","category-technical-resources"],"_links":{"self":[{"href":"https:\/\/www.biaotuoboard.com\/wp-json\/wp\/v2\/posts\/1686","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.biaotuoboard.com\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.biaotuoboard.com\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.biaotuoboard.com\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.biaotuoboard.com\/wp-json\/wp\/v2\/comments?post=1686"}],"version-history":[{"count":0,"href":"https:\/\/www.biaotuoboard.com\/wp-json\/wp\/v2\/posts\/1686\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.biaotuoboard.com\/wp-json\/wp\/v2\/media?parent=1686"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.biaotuoboard.com\/wp-json\/wp\/v2\/categories?post=1686"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.biaotuoboard.com\/wp-json\/wp\/v2\/tags?post=1686"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}